Description
- Primary use:
This product is commonly seen on bar tops and table tops in many bars and restaurants. - Application:
The product should be applied in two stages. The first stage is referred to as the seal coat. The seal coat is brushed on in a thin layer and is used to seal any pores in the surface and prevent air bubbles from forming in the following flood coats. This stage is followed by the flood coat, which will flow and self level, clean brushes or squeeges can be used to help spread the epoxy. Flood coats are applied in 1/8″ layers at a time, as many as desired can be applied, however one to three coats is average for most table or bar coatings. - Recoating/Between Layers:
Recoating can usually be be done within 4 to 8 hours. If re-coated within this time period no sanding is necessary between layers.
If your previous layer has fully dried, light sanding with 220 or 320 grit sandpaper is recommended to achieve a good bonding surface. After sanding you should wipe down with a solvent such as denatured alcohol, acetone or lacquer thinner to remove any impurities from the surface. (do NOT use mineral spirits) - Embedding Pictures:
Objects, such as pictures, maps etc. can be imbedded in this product during the pours. Most photo quality paper does not require any special preparation however sometimes thin paper objects must first be sealed with a white glue or similar product to prevent the epoxy from fully penetrating the paper and causing it to become transparent. - Embedding Solid Objects (wood, rocks, shells, etc.)
All porous materials should first have a seal coat of epoxy applied. This will prevent air bubbles from occurring in subsequent flood coats. Usually the objects can be set in place before sealing. - Working Conditions:
For best results the product should be used at temperatures from 70-80 degrees F. The room which you are working should be clean, dry, dust and insect free. Settling dust can often cause blemishes on the glassy surface. - Exterior Applications:
Please not that although this product will resist yellowing better than other epoxies it is NOT 100% UV resistant. Continuous outdoor UV exposure over months or years will cause the finish to lose its gloss and cause gradual changes in color.Coverage: See the coverage calculators below to figure out how much table top epoxy you need for your bar top or project. Remember not to combine seal and flood coat coverages.
Amount of Table Top Epoxy needed for rectangular areas
Flood coats are designed to go on approximately 1/8″ or .125″ thick,
Seal coat coats are just thick enough to seal any bubbles or dust in place and only need to be .02″ thick.
Example: A 6ft x 4ft bare wood table (24sq ft) would require 2 Quarts to complete ONE seal coat and about a gallon and a half to complete ONE flood coat for a total of Two Gallons.
Amount of Table Top Epoxy needed for circular areas
Recommended Supplies
Graduated Mixing Cups – An accurate measurement is extremely important to achieve optimum curing.
Applicators – Rubber squeeges are simple to use and leave no air bubbles. Foam brushes and nylon bristle brushes are preferred with epoxy, make sure there are no loose hairs.
Hair Drier, Heat Gun or Torch – These are used after the pour is completed and the epoxy is still liquid. A very smooth stroke across about 6-12 inches above the epoxy surface will burst remaining air bubbles.
Andy I (verified owner) –
This product rocks. Easy to use, even for a beginner.
Cameron (verified owner) –
I ordered the table top epoxy to finish the bar that I made in my rec room. When I called in I spoke with Chris who told me exactly what i needed, how much and what to expect. Everything he said worked out exactly as it was explained to me. I am very happy knowing that the people at illstreet are informed about their products , and have worked with them in the past. From now on any thing that i need that is sold here I will be giving you guys a call first.
Thanks
Cameron
Ethan (verified owner) –
No complaints it’s good stuff I use it to coat paintings and woodwork takes awhile to dry but that’s nice gives it plenty of time to level out I will get more.
Ethan (verified owner) –
It’s good stuff I will get more.
Sue Ore (verified owner) –
Good stuff. It was my first time using this material to do our countertops and they look amazing. Will definitely be buying more in the future.
Robert (verified owner) –
Love this tabletop epoxy!
K.Young (verified owner) –
Am looking forward to trying/using this epoxy and the Laminating resin for woodwork and art.
Joe (verified owner) –
I received my first order of this stuff. I am happy to be able to work with pouring this product versus having to use an large oven. I am still trying to get the process down so its as clear as possible. I ordered the 1:1 pumps to go with the 2 part component but the hardener is too thick. I have to find 2 kitchen basters with ML measurements and that seems to be much more productive. So far I like this product but will need graduate myself from beginner to experienced.
Rian Black (verified owner) –
The epoxy works great and gives excellent results when done correctly. Lays down about 1/8" thick and is highly durable once completely cured. I’ve done a few bar tops and kitchen islands and have never had a problem.